How Much Gravel for a 10×20 Driveway?

Updated November 2026

A 10×20 ft driveway is one of the most common gravel jobs there is: a single-car driveway, deep enough to drive on every day. Here is the full answer for that exact size, with the math shown slowly so you can copy the same steps for any other size.

Quick Answer

A 10 × 20 ft driveway at the standard 4 inches deep needs about 2.5 cubic yards of gravel, roughly 3.5 tons. With the usual 10% extra for settling and low spots, order about 2.7 cubic yards (3.8 tons). In 0.5 cu ft store bags that is about 147 bags to order, which is why bulk delivery usually wins at this size.

Your size or depth is different? The Gravel Calculator gives you cubic yards, tons and bag count for any length, width and depth.

The Math, Step by Step

Step 1: Find the area in square feet. Length × width = 10 ft × 20 ft = 200 sq ft. (Not sure of your area yet? The Square Feet Calculator works it out from your measurements.)

Step 2: Change the depth to feet. Driveways need 4 inches of gravel as a standard layer. 4 ÷ 12 = 0.33 ft.

Step 3: Find the volume in cubic feet. Area × depth = 200 × 0.33 = about 67 cubic feet.

Step 4: Change to cubic yards. Cubic feet ÷ 27 = 67 ÷ 27 = 2.47 cubic yards, which rounds up to about 2.5. The Cubic Yard Calculator does this change for you.

Step 5: Change to tons. Gravel is often sold by the ton. One cubic yard of normal gravel weighs about 1.4 tons, so 2.47 × 1.4 = about 3.5 tons. With the 10% extra, order about 3.8 tons.

Step 6: Bags, if you go that way. Most store bags of gravel hold 0.5 cubic feet. 67 ÷ 0.5 = 134 bags exact, and with the 10% extra you would buy about 147 bags. That is a lot of bags to carry, which is why most people order bulk for a driveway.

Gravel Needed by Depth

Not sure which depth to use? Here are the numbers for a 10 × 20 ft driveway at three common depths. Every figure includes the 10% extra, so these are the amounts to actually order.

Depth Cubic yards to order Tons to order 0.5 cu ft bags to order
2 inches 1.4 yd³ 1.9 tons 74 bags
4 inches (standard) 2.7 yd³ 3.8 tons 147 bags
6 inches (heavy use) 4.1 yd³ 5.7 tons 220 bags

For a standard home driveway, 4 inches is the right depth. Use 6 inches if the driveway will carry trucks or heavy equipment regularly.

A 10 × 20 ft Driveway at 4 Inches Deep 20 ft 10 ft Top view: 200 sq ft of gravel 4 in Side view gravel soil below Depth: 4 inches of gravel

A 10 × 20 ft driveway: 200 sq ft, covered 4 inches deep. That is about 67 cubic feet of gravel before the extra.

Bags or Bulk Delivery?

For a 10×20 driveway you need about 2.7 cubic yards to order. At that size, bulk delivery is almost always cheaper than bags.

Bagged gravel: the standard 0.5 cu ft bag costs roughly $4 to $6 at most stores. For about 147 bags that is roughly $600 to $900 in material alone, plus the time and effort to haul and carry every bag.

Bulk gravel: delivered by the yard or by the ton. Prices vary a lot by area, but the same job usually comes to roughly $115 to $210 for the material before any delivery fee, far less than bags.

Please note: These are example prices only. Prices change by area, supplier and type.

Bagged gravel makes sense for small patch repairs, or if no bulk supplier delivers to your area.

Common Gravel Types for Driveways

Gravel type Best for Notes
#57 crushed stone Base layer Most common driveway gravel
Pea gravel Top decorative layer Rolls underfoot, needs edging
Crusher run Full driveway base Compacts well, good drainage
River rock Decorative only Not recommended as a driving surface

For most driveways, #57 crushed stone or crusher run is the standard choice.

Mistakes to Avoid

Going too shallow. Less than 4 inches and the gravel shifts and thins out quickly under tire traffic.

Skipping edging. Without borders, gravel spreads into the lawn over time. Metal or plastic landscape edging keeps it in place.

Not adding a base layer first. For new driveways, a layer of larger base stone (like #2 crushed stone) under the top gravel extends the life of the driveway significantly.

Ordering the exact amount. Always add about 10% extra to your order for edges, uneven ground and settling. Every number in the depth table above already includes it.

Your Size Is Different?

🧮 Use the Gravel Calculator: Type any length, width and depth and get cubic yards, tons and bags in seconds.

Questions People Ask

How much gravel do I need for a 10×20 driveway?

About 2.5 cubic yards (roughly 3.5 tons) at the standard 4-inch depth. Order about 2.7 cubic yards (3.8 tons) once you add the usual 10% extra. In 0.5 cu ft store bags, that is about 147 bags to order.

How deep should driveway gravel be?

Four inches is standard for a home driveway. If the driveway carries heavy trucks or equipment regularly, use 6 inches.

How many cubic yards is a ton of gravel?

About 0.7 cubic yards. One cubic yard of normal gravel weighs about 1.4 tons (about 2,800 lb), so for a 10×20 driveway at 4 inches deep you need about 3.5 tons, or 3.8 tons with the extra included.

How much does gravel cost for a 10×20 driveway?

Bulk delivery for about 2.7 cubic yards usually comes to roughly $115 to $210 for the material before any delivery fee, and prices vary a lot by area. The same job in 0.5 cu ft bags runs roughly $600 to $900 in bags alone.

Can I use the same calculator for other sizes?

Yes. The Gravel Calculator handles any length, width and depth and gives you cubic yards, tons and bag count right away.

More Example Guides

Please note: Results are estimates. Ground conditions, edging and waste vary by project. Always measure twice before ordering material.

Planning a bigger job for a customer? Our free Estimate Maker turns your numbers into a clean estimate.