Wall Square Footage Calculator
Free calculator with worked examples, room tables and paint estimates. Last updated October 2026.
This wall square footage calculator works out how much wall you have to cover, with the doors and windows already taken off. People also search for it as a wall square feet calculator or a wall area calculator. Enter one wall at a time, or a whole room, and get the area for paint, wallpaper, drywall or tile. This free calculator needs no sign-up and no email.
Table of Contents
Wall Square Footage Calculator
Each door takes off 21 sq ft and each window takes off 15 sq ft, the standard sizes below. When you buy paint, round the amount up to the next quart or gallon so you do not run short near the end.
How to Calculate the Square Footage of a Wall
One wall: Wall area = Length × Height
Whole room: Wall area = 2 × (Length + Width) × Height, then subtract the doors and windows.
One wall
Measure the wall from end to end, then from the floor to the ceiling, and multiply the two numbers. A wall 10 ft long and 8 ft high is 10 × 8 = 80 sq ft.
A whole room
A normal room has two pairs of matching walls. Add the room length and width, double the answer to cover all four walls, then multiply by the wall height.
Worked example, a 12 × 10 ft room with 8 ft walls:
Long walls: 2 × 12 × 8 = 192 sq ft
Short walls: 2 × 10 × 8 = 160 sq ft
All four walls: 192 + 160 = 352 sq ft
Doors and windows: one door 21 sq ft + one window 15 sq ft = 36 sq ft
Wall area to cover: 352 − 36 = 316 sq ft
Subtract the openings
Doors and windows are wall you do not paint, paper or board over, so take them off at the end. The calculator above does this for you with the standard sizes in the next table. If your doors or windows are much bigger than standard, measure them, multiply length by height for each one, and subtract that area instead.
Standard Door and Window Sizes
Most openings in a house are close to these standard sizes, so they are safe to use when you do not want to measure every one:
| Opening | Standard Size | Area to Subtract |
|---|---|---|
| Standard door | 3 × 7 ft | 21 sq ft |
| Double door | 6 × 7 ft | 42 sq ft |
| Standard window | 3 × 5 ft | 15 sq ft |
| Large window | 4 × 5 ft | 20 sq ft |
| Sliding glass door | 6 ft × 6 ft 8 in | About 40 sq ft |
| Garage door (single) | 9 × 7 ft | 63 sq ft |
| Garage door (double) | 16 × 7 ft | 112 sq ft |
Working in metric? A standard door there is about 0.9 × 2.1 m, which is 1.89 sq m, and a standard window is about 0.9 × 1.5 m, which is 1.35 sq m. The calculator uses those sizes when you pick metric units.
Wall Area of Common Rooms
These are the full four walls of each room, before taking off any doors and windows:
| Room Size | Walls at 8 ft Ceiling | Walls at 9 ft Ceiling |
|---|---|---|
| 8 × 10 ft | 288 sq ft | 324 sq ft |
| 10 × 10 ft | 320 sq ft | 360 sq ft |
| 10 × 12 ft | 352 sq ft | 396 sq ft |
| 12 × 12 ft | 384 sq ft | 432 sq ft |
| 12 × 14 ft | 416 sq ft | 468 sq ft |
| 12 × 16 ft | 448 sq ft | 504 sq ft |
| 14 × 16 ft | 480 sq ft | 540 sq ft |
| 15 × 20 ft | 560 sq ft | 630 sq ft |
| 16 × 20 ft | 576 sq ft | 648 sq ft |
A taller ceiling adds more wall than most people expect. The same 12 × 12 ft room grows from 384 sq ft of wall at 8 ft to 432 sq ft at 9 ft, which is about a pint more paint per coat.
What to Do With Your Wall Area
Paint
One gallon of paint covers about 350 sq ft per coat. Divide your wall area by 350 to get the gallons for one coat, and double it for two coats. The 316 sq ft room above needs 316 ÷ 350 = about 0.9 gallons for one coat, so buy 1 gallon, and 2 gallons for two coats. For primer, walls with patches, or a big color change, use the full Paint Calculator.
Wallpaper
In the US, wallpaper is usually sold in double rolls of about 56 sq ft (a single roll is about 28 sq ft). After matching the pattern and trimming, plan on about 25 sq ft of usable wall per single roll (about 50 sq ft per double roll), and less with a large pattern repeat. 316 sq ft ÷ 25 = about 13 single rolls, or 7 double rolls. Roll sizes vary by brand and country, so check the label.
Drywall
A standard drywall sheet is 4 × 8 ft, which is 32 sq ft. Divide your wall area by 32: 316 ÷ 32 = 9.875, so 10 sheets for that room, plus a spare for cuts and mistakes. The Drywall Calculator also works out screws and joint compound.
Tile and backsplash
The same number works for a tiled wall or a kitchen backsplash. Measure just that part of the wall, length by height, and buy tile for that area plus about 10% extra for cuts.
Common Mistakes
1. Forgetting the doors and windows
One door and one window already remove 36 sq ft. Skip the subtraction and you buy paint, paper or sheets for wall that is not there.
2. Measuring only one wall
A room has four walls, and the pair of short walls is easy to forget. Use the room formula, 2 × (length + width) × height, so every wall is counted once.
3. Using the floor area instead of the wall area
Floor area and wall area are very different numbers. A 12 × 10 ft room has 120 sq ft of floor but 352 sq ft of wall at an 8 ft ceiling. Paint goes on the walls, so always use the wall number.
4. Mixing inches and feet
If the wall height is 8 ft 6 in, enter 8.5, not 8.6. Six inches is half a foot, so divide the inches by 12 before you add them to the feet.
Gable and Cathedral Walls
Not every wall is a plain rectangle. Split a shaped wall into simple shapes, work each one out, and add the answers together.
Gable wall (the triangle-topped end wall of a house): work out the rectangle part as normal, then add the triangle on top: wall length × rise ÷ 2, where the rise is how far the peak sits above the top of the straight wall. A 20 ft wide wall with a 6 ft rise adds 20 × 6 ÷ 2 = 60 sq ft.
Cathedral wall (one sloped top edge): use ½ × (short height + tall height) × length. For a wall 12 ft long, 8 ft high at one end and 14 ft at the other: ½ × (8 + 14) × 12 = 132 sq ft.
Then subtract the doors and windows as normal.
Frequently Asked Questions
What is the formula for the square footage of a wall?
Length × height. For one wall, multiply its length by its height. For a whole room, use 2 × (length + width) × height, then subtract the area of the doors and windows.
How do I include doors and windows?
Work out the full wall area first, then take the openings off. A standard door takes off 21 sq ft and a standard window takes off 15 sq ft. One door and one window together remove 36 sq ft. The calculator on this page does the subtraction for you.
How many square feet is a standard door?
21 square feet. A standard door is 3 ft wide and 7 ft high, and 3 × 7 = 21.
What is the wall area of a 12 × 12 ft room with 8 ft walls?
384 sq ft for all four walls: 2 × (12 + 12) × 8 = 384. Take off about 36 sq ft for one door and one window and about 348 sq ft of wall is left to cover.
How much paint do I need for a 12 × 12 ft room?
One gallon covers about 350 sq ft per coat. The room has about 348 sq ft of wall after the door and window come off, so about 1 gallon for one coat and about 2 gallons for two coats. Round up when you buy.
Does the ceiling count as wall area?
No. Wall area is the walls only. For a flat ceiling, its area equals the floor area: length × width.
How do I measure a gable or cathedral wall?
Split the wall into simple shapes and add them. For a gable, work out the rectangle as normal, then add the triangle on top: wall length × rise ÷ 2, where the rise is how far the peak sits above the top of the straight wall. A 20 ft wide wall with a 6 ft rise adds 20 × 6 ÷ 2 = 60 sq ft. For a sloped (cathedral) wall, use ½ × (short height + tall height) × length. For a wall 12 ft long, 8 ft high at one end and 14 ft at the other: ½ × (8 + 14) × 12 = 132 sq ft.
Areas and paint amounts on this page are estimates for planning. Measure each wall before you buy, and add about 10% extra material for cuts, pattern matching and mistakes.
